ReadyPlanet.com
dot dot
dot
BRAND NAME
dot
bulletMAGNESCALE/SONY
bulletSK (NIIGATA SEIKI)
bulletVALCOM
bulletARROW
bulletTECLOCK
bulletONO SOKKI




ELECTRONIC INSTRUMENT
PD-512P
PD-512N
SD-1201
Digital indicator
  • Small, right and thin type : the most suitable for simultaneous measurement of many points.
  • Resolution : 0.001mm and 0.005mm
  • Measuring range : 12mm
  • Anti-circumstance equivalent to IP 64( PD- 512P)
  • Complying to auto-measuring line by using air lifter.
Digital counter
  • As this is small and light, it is easy to be built in various equipments.
  • Measured data / max. figure / minimum figure / p-p figure / the result judgment / operative function are equipped as standard. It consists of 1CH and 2 CH.
  • Out put complies with BCD,RS-232.

PD-012P
PD-012N
SD-0205
Digital indicator
  • Small, right and thin type : the most suitable for simultaneous measurement of many points.
  • High resolution : 5um and 10um
    *Measuring range : 12mm
  • Anti-circumstance equivalent to IP 64( PD- 012P )
  • Complying with auto-measuring line by using air lifter
Digital counter
  • As this is small and light, it is easy to be built in various equipment.
  • Measured data / Max figure / minimum figure / p-p figure / the result judgment / operative function are equipped as standard. It consists of 1CH and 2 CH.
  • Out put complies with BCD,RS-232

  • This is as compact size as standard dial gauge to some extent. The application range is further expanded.
  • Indication part can be optionally revolved up to 330°.In case it is slanted and used, it can be set with the glance of operators.
  • Above sensor stroke can be indicated by using pre-set function.
  • Tolerance judging measurement is possible by using tolerance set up function.
  • Button type battery is built in for power source and it can be used for a long period without code. (continuous usage : approx. 5000 hours )
  • Setting 0 point in every power ON is not needed, as ABS (absolute) scale with absolute original point is built in.
  • Treating statistics data and print out are possible by connecting to optional printer SD-763N.
PC-440

  • Tolerance can be set in the wide range of 0~5mm and it can be judged with lighting lamp apart from indication figure of dial gauge.
  • It can be directly connected to sequencer by protect circuit.
PU-490

  • Dimension of springs and pressing parts used for precision machinery, computer terminal and electric goods etc. can be measured just before its shape is charged by measurement power.
  • When contract of sensor (gauge head) and work is detected by energization, buzzer rings. Scale mark of gauge is read at that time.
  • A stir by 10mm can be adjusted by upper knob.
  • Work of max 150mm can be measured by using block gauge.
  • Work without energization can not be measured as it is detected by energization.
SD-101

  • This is a specialized instrument which comparatively measures inner diameter and outer diameter.
  • After placing master gauge to measuring table and setting standard figure ( set at “0” point ), tolerance judgment against standard figure is measured by measuring work.
  • Ultra hard alloy are applied for gauge head and anvil (anvil pin).
  • Special ordered product is utilized for the measuring range except for the following list.




TECLOCK

DUROMETER
OTHER PRECISION MEASUREMENT INSTRUMENT
BORE GAUGE
CALIPER GAUGE
DEPTH GAUGE
THICKNESS GAUGE
LEVER TEST
DAIL INDICATOR



Copyright © 2010 All Rights Reserved.
บริษัท วรีพิทักษ์ จำกัด Tel:038-783850, Fax: 038-270479 Email: nida_y@hotmail.com